Silicone Cold Shrink Tube for 7/16 DIN RF Connector


Cold shrink tube is designed for weatherproofing protection on connections between jumper cable and connector (7-16 DIN, N type or 4.3-10) of wireless equipment, such as RRU, Antenna and Microwave. Comparing with tape sealing protection, cold shrink tube installation is much shorter (15-30 seconds), convenient installation, uniform appearance for acceptance.

المميزات

» Easy and quick installation

»لا يحتاج لأى أدوات ولا تسخين

»استقرار حراري جيد

»تستوعب مجموعة كبيرة من أحجام الكابلات

»مقاومة ممتازة للتمزق

» UV and ozone aging resistant

Note: In certain applications, a foam tape will be needed for smaller cable diameter that cannot be covered with the tube range, the foam tape is used to increase the smaller cable diameter and assure the sealing of clod shrink tube.

تركيب الانكماش البارد

 

Properties

ItemParameter and ResultTest Method
ضد للماءClassPass, IPX7IEC 60529:1989/AMD2:2013/COR1:2019

1 meter depth in water, duration: 30 minutes

Physical and mechanical propertiesShore HardnessA/41/1ASTM D2240-15
قوة الشد9.66 MPaASTM D412-16 Method A
Elongation930%ASTM D412-16 Method A
قوة الدموع28.4 N/mmASTM D624-00
Brittleness Temperature by ImpactالبشريASTM D746-14,-60℃
Drop Testالبشري

No damage, deformation, and support tube could be pulled out normally

Drop from height 1.2m on tile floor surface, 3 times to test
FlammabilityHorizontal BurningHBUL 94-2013 Rev.14-2022 Section 7
Electricityقوة عازلة19.10 KV/mmASTM D149-20 Method A
Performance under harsh environmentMechanical and Waterproof PropertiesNo crack, discoloration, damage or deformation,

IPX7 Pass

 

1. Dry heat test (IEC 60068-2-2:2008 Test Bb): 90±2℃,168 hours;

2. Low temperature test (IEC 60068-2-1:2008Test Ab): -40±2℃,168 hours;

3. Thermal cycling test: Cycle time:12h/cycle, Cycle index: 10 cycles, Total duration: 120 hours;

4. Damp heat test, cyclic test (IEC 60068-2-30:2005 Test Db):Cycle time:24h/cycle, Cycle index: 10 cycles, Total duration: 240 hours;

5. Damp heat test, steady state (IEC 60068-2-78:2012 Test Cab):Temperature: 75±2℃, Humidity:(95±1) %RH, Total duration: 1000 hours

Aging TestLight Aging Test-UV ExposureNo crack, discoloration, damage or deformation

Grey scale: 4-5

IPX7 Pass

ISO 4892-3:2016Cycle1& ISO 105-A02:1993/Cor.2:2005

Lamp type: UVA-340, 8h UV at (60±3)℃ BPT,0.76W/(m²×nm)@340nm

4h condensation at(50±3)℃ BPT

Exposure duration:1000 hours

Ozone AgingNo crack, discoloration, damage or deformation,

IPX7 Pass

ASTM D1149-16 Method B procedure B1

Temperature: 40±1℃

Ozone concentration:50±5 pphm

Exposure duration: 72 hours

Hailstone Resistant TestNo crack,damage or deformationIEC 61215,φ20mm hailstone falling
موادEnvironmental ProtectionRoHS

Reach

IEC 62321

SVHC

درجة الحرارةInstallation Temperature-40℃ ∼ 60℃Refer to “mechanical properties” and “performance under harsh environment”
Operation Temperature-60℃ ∼ 80℃
Stock Temperature-60℃ ∼ 80℃

 

التطبيقات

»يوفر حماية مادية ممتازة ومانع تسرب الرطوبة لموصلات وكابلات الاتصالات.

»تطبيق مثالي لاتصالات وحدة الراديو عن بعد.

»إصلاح سترة الكابل والغمد.

»حماية التركيبات والوصلات من التآكل.

 

معلومات سريعة


Product Name: Cold Shrink Tube
Product Code: CST40-125-DIN
المادة: سيليكون مطاط
Inner Diameter of Plastic Core: 40mm
Diameter (after shrink): 10mm
Length (after shrink): 125mm
Application: Sealing 7/16 din connector to 1/2" cable
موك: 1000
عينة معروضة: مجانًا على حسابنا
طريقة الشحن: الطريق البحري ، الطريق الجوي ، DHL ، UPS ، FedEx ، إلخ.
ميناء الشحن: شنغهاي ، الصين

أنبوب الانكماش البارد من مطاط السيليكون لموصل 5G Nex10