Cold Shrink Tube Silicone Rubber for Weather Proof
Cold Shrink Tube, also is known well as “Cold Shrink Wrap”, is manufactured with silicone rubber for weatherproofing protection on telecommunication equipment connections, such as RRU, Antenna and Microwave. Comparing with tape sealing protection, cold shrink tube installation is much shorter (15-30 seconds), convenient installation, uniform appearance for acceptance.
Характеристики
» Easy and quick installation
»Не требует никаких инструментов или тепла.
»Обеспечивает хорошую термическую стабильность.
»Подходит для кабелей широкого диапазона размеров
»Отличная устойчивость к разрыву
» UV and ozone aging resistant
Note: In certain applications, a foam tape will be needed for smaller cable diameter that cannot be covered with the tube range, the foam tape is used to increase the smaller cable diameter and assure the sealing of clod shrink tube.
Properties
| Item | Parameter and Result | Test Method | |
| Водонепроницаемый | Class | Pass, IPX7 | IEC 60529:1989/AMD2:2013/COR1:2019 1 meter depth in water, duration: 30 minutes |
| Physical and mechanical properties | Shore Hardness | A/41/1 | ASTM D2240-15 |
| Предел прочности | 9.66 MPa | ASTM D412-16 Method A | |
| Elongation | 930% | ASTM D412-16 Method A | |
| Сила слезы | 28.4 N/mm | ASTM D624-00 | |
| Brittleness Temperature by Impact | Проходить | ASTM D746-14，-60℃ | |
| Drop Test | Проходить No damage, deformation, and support tube could be pulled out normally | Drop from height 1.2m on tile floor surface, 3 times to test | |
| Flammability | Horizontal Burning | HB | UL 94-2013 Rev.14-2022 Section 7 |
| Electricity | Диэлектрическая прочность | 19.10 KV/mm | ASTM D149-20 Method A |
| Performance under harsh environment | Mechanical and Waterproof Properties | No crack, discoloration, damage or deformation, IPX7 Pass
| 1. Dry heat test (IEC 60068-2-2:2008 Test Bb): 90±2℃，168 hours; 2. Low temperature test (IEC 60068-2-1:2008Test Ab): -40±2℃，168 hours； 3. Thermal cycling test: Cycle time:12h/cycle, Cycle index: 10 cycles, Total duration: 120 hours; 4. Damp heat test, cyclic test (IEC 60068-2-30:2005 Test Db)：Cycle time:24h/cycle, Cycle index: 10 cycles, Total duration: 240 hours; 5. Damp heat test, steady state (IEC 60068-2-78:2012 Test Cab)：Temperature: 75±2℃, Humidity：(95±1) %RH, Total duration: 1000 hours |
| Aging Test | Light Aging Test-UV Exposure | No crack, discoloration, damage or deformation Grey scale: 4-5 IPX7 Pass | ISO 4892-3:2016Cycle1& ISO 105-A02:1993/Cor.2:2005 Lamp type: UVA-340, 8h UV at (60±3)℃ BPT，0.76W/(m²×nm)@340nm 4h condensation at(50±3)℃ BPT Exposure duration:1000 hours |
| Ozone Aging | No crack, discoloration, damage or deformation, IPX7 Pass | ASTM D1149-16 Method B procedure B1 Temperature: 40±1℃ Ozone concentration:50±5 pphm Exposure duration: 72 hours | |
| Hailstone Resistant Test | No crack,damage or deformation | IEC 61215,φ20mm hailstone falling | |
| Материал | Environmental Protection | RoHS Reach | IEC 62321 SVHC |
| Температура | Installation Temperature | -40℃ ∼ 60℃ | Refer to “mechanical properties” and “performance under harsh environment” |
| Operation Temperature | -60℃ ∼ 80℃ | ||
| Stock Temperature | -60℃ ∼ 80℃ | ||
How to Install a Cold Shrink Tube
